15BY25 15mm Stepper Motor | MAINTEX Direct Factory For Custom Micro Motors
MAINTEX is the source factory for 15mm PM stepper motors (tin‑can claw‑pole motor ), with 20 years in miniature permanent‑magnet stepper motor R&D and production. We make key parts including magnetic rings, cables, and plastic components in-house, then finish assembly on-site. Our 30+ automated lines are our 3rd-gen in-house developed equipment, hitting 600,000 units per day. We adjust shaft, leads, connectors and winding parameters to match your needs. All permanent magnet stepper motors meet ISO9001, IATF16949, RoHS and REACH for global shipment.
Popular 15mm Stepper Motors For Your Device
We carry a range of 15BY25 mini stepper motors in 3V‑24V, with different torque and body sizes. If no stock unit fits your OEM project, send your specs for matching or custom 15mm stepper motor solutions.

Works under frequent start‑stop cycles. Used in thermal printers and POS terminal drive structures.
- Model: 15BY25‑561D
- Rated Voltage: 5V
- Holding Torque: 35gf.cm
- Dimensions: φ15×10.3mm
- Max No‑load Pull‑out Frequency: ≥1600PPS

For small‑angle adjustment in tight spaces. Used in label printers and compact printing devices.
- Model: 15BY25‑558A
- Rated Voltage: 5V
- Holding Torque: 30gf.cm
- Dimensions: φ15×10.3mm
- Max No‑load Pull‑out Frequency: ≥1500PPS

Handles frequent intermittent start‑stop cycles . Used in fast‑moving parts of smart home hardware.
- Model: 15BY25‑471A
- Rated Voltage: 7.4V
- Holding Torque: 40gf.cm
- Dimensions: φ15×10.3mm
- Max No‑load Pull‑out Frequency: ≥1500PPS

Runs at medium operating speed. Used in robot joints, toys and small smart locks.
- Model: 15BY25‑405A
- No‑load Speed: 2100RPM
- Holding Torque: 30gf.cm
- Dimensions: φ15×11.1mm
- Max No‑load Pull‑out Frequency: ≥1000PPS

Operates from low‑voltage battery power. Used in battery‑run portable and handheld devices.
- Model: 15BY25‑490H
- Rated Voltage: 3V
- Holding Torque: 30gf.cm
- Dimensions: φ15×10.3mm
- Max No‑load Pull‑out Frequency: ≥900PPS

Accepts higher load for long daily runtime. Used in small automation modules.
- Model: 15BY25‑339
- Rated Voltage: 24V
- Self‑Positioning Torque: 13 gf · cm
- Holding Torque: 30 gf · cm
- Dimensions: φ15×19.5mm
Why Choose Our 15mm PM Stepper Motors
We test and share real claw pole motor data, not just static holding torque. Batch outputs stay consistent for your testing.

Pure‑copper winding, no copper‑clad aluminum

≤40dB at 10cm no-load, fits noise-sensitive devices

Lower heat generation, reduces thermal failure risk

Up to 10000‑hr continuous operation under rated conditions

Dynamic torque tested, do not rely only on static holding torque

Tight control on resistance, inductance and torque spread

Direct replacement, no new molds or mechanical redesign

Notify you in advance for critical component revisions
How to choose 15mm stepper motor winding
If you build high-speed thermal printers or 5V POS devices, choose low inductance winding of 2–4 mH. It holds enough dynamic torque at high PPS and helps you avoid step loss or paper jams. High inductance winding works for your low-speed valves, meters and some toys; it runs steady and uses less current. For your 3V / 3.3V battery-powered equipment, we make separate windings. Do not reuse 5V winding designs, or you will get a big torque drop. If you use 24V industrial boards, go for our 24V version. It has a longer body and higher rated torque.


Can I customize this 15mm tin-can stepper motor
Low-cost, fast-turn minor changes are available. We can adjust shaft length and profile, modify lead length and exit angle, or swap terminals and connectors. Winding resistance and inductance can be fine-tuned to match your driver board. Rated voltage can also be adjusted within the existing magnetic circuit, plus custom neutral packaging and labels. Stator size changes, reworked magnet circuits or brand-new housing structures fall under full new development. These need NRE tooling and a longer lead time.
Resource

To learn more about our range of 15mm micro PM stepper motor, please download the complete catalog.

Download datasheets for our representative 15mm PM stepper motor models. For complete specifications or custom technical drawings, please contact our engineering team.
15mm Stepper Motor Manufacturer in China


At MAINTEX, we manufacture 15mm stepper motors. Our 45,000㎡ factory hits 600K units of daily output. We hold 225+ patents and helped develop 12 national standards, including 2 GJB military standards. We offer a 2‑year warranty with remote support from our 70‑member R&D team. We’ve finished 3000+ projects across 100+ countries. You can track your order, get full batch test records, and count on 72h 8D failure analysis.
15mm Stepper Motor Application Solutions

MAINTEX 15mm 15mm miniature tin‑can stepper motors drive the paper feed for receipt printers and portable label printers. Do not only focus on static holding torque; dynamic torque at high speed is what really matters. We guarantee consistent batches, low noise and vibration, stable torque across wide temperatures, and bend-resistant leads. No random paper jams after mass production even if samples test well.

This 15mm stepper motor suits motion joints for educational robots, STEM kits and toys. You usually run it with simple 5V drivers and keep tight cost control. We can custom wires and terminals for you. Noise standards are not strict here. Your orders will follow seasonal cycles, and we won’t raise MOQ only for wiring adjustments.

This 15mm mini stepper motor runs micro valves, water meters and air deflectors in smart home assemblies. It locks firmly when power cuts off and draws little current, working well with 3.3V and 5V battery boards. Torque stays steady after long idle time to prevent positioning and locking failure.

MAINTEX 15mm stepper motors fit compact medical analyzers and small medical printers. We provide full batch traceability, test reports and material documentation. All motors pass insulation and voltage withstand tests. We will not swap magnets or key components without notice, to keep your medical compliance valid.

For compact PTZ cameras and small automation positioning systems, our 15mm stepper motors work reliably. Every unit is carefully tuned. We control shaft runout and suppress vibration, so you avoid camera shake and blurry video output.
More About Our Factory
- 15mm Stepper Motor Table
- Gallery
Check our overview table to pick the right 15mm mini stepper motor type for your project.
| Rate Voltage | Resistance | Inductance | Step Angle | Exciting Method | Max No-load Pull-in Frequency | Max No-load Pull-out Frequency | Self-Positioning Torque (min) | Holding Torque(min) | Rated Frequency | No-load Speed | Rated Torque (min) | Dimensions |
| 5V | 8.3Ω±10% | 3.1mH±20% | 18° | 2-2 | ≥1000PPS | ≥1500PPS | 7gf.cm | 30gf.cm | 800PPS | 2400RPM | 15gf.cm | φ15mm*10.3mm |
| 5V | 10Ω±10% | 3.4mH±20% | 18° | 2-2 | ≥1100PPS | ≥1500PPS | 7gf.cm | 30gf.cm | 800PPS | 2400RPM | 13gf.cm | φ15mm*10.3mm |
| 5V | 10Ω±10% | 3.4mH±20% | 18° | 2-2 | ≥1100PPS | ≥1500PPS | 7gf.cm | 30gf.cm | 800PPS | 2400RPM | 13gf.cm | φ15mm*10.3mm |
| 5V | 5.5Ω±10% | 2.0mH±20% | 18° | 2-2 | ≥1200PPS | ≥1600PPS | 7gf.cm | 35gf.cm | 800PPS | 2400RPM | 15gf.cm | φ15mm*10.3mm |
| 5V | 10Ω±10% | 3.4mH±20% | 18° | 2-2 | ≥1100PPS | ≥1500PPS | 7gf.cm | 30gf.cm | 800PPS | 2400RPM | 13gf.cm | φ15mm*11.1mm |
| 5V | 12Ω±10% | 4.0mH±20% | 18° | 2-2 | ≥1100PPS | ≥1500PPS | 7gf.cm | 30gf.cm | 800PPS | 2400RPM | 12gf.cm | φ15mm*11.1mm |
| 5V | 29Ω±10% | 9.0mH±20% | 18° | 2-2 | ≥800PPS | ≥1000PPS | 7gf.cm | 30gf.cm | 700PPS | 2100RPM | 7gf.cm | φ15mm*11.1mm |
| 5V | 29Ω±10% | 9.0mH±20% | 18° | 2-2 | ≥800PPS | ≥1000PPS | 7gf.cm | 30gf.cm | 700PPS | 2100RPM | 8gf.cm | φ15mm*11.1mm |
| 5V | 10Ω±10% | 3.4mH±20% | 18° | 2-2 | ≥1100PPS | ≥1500PPS | 7gf.cm | 30gf.cm | 800PPS | 2400RPM | 13gf.cm | φ15mm*11.1mm |
| 5V | 3.5Ω±10% | 1.1mH±20% | 18° | 2-2 | ≥1000PPS | ≥1500PPS | 7gf.cm | 30gf.cm | 800PPS | 2400RPM | 8gf.cm | φ15mm*11.1mm |
| 5V | 10Ω±10% | 3.4mH±20% | 18° | 2-2 | ≥1000PPS | ≥1500PPS | 7gf.cm | 30gf.cm | 500PPS | 1500RPM | 15gf.cm | φ15mm*10.5mm |
| 3V | 15Ω±10% | 5.0mH±20% | 18° | 2-2 | ≥700PPS | ≥900PPS | 7gf.cm | 30gf.cm | 700PPS | 2100RPM | 10gf.cm | φ15mm*10.3mm |
| 7.4V | 8.5Ω±10% | 3.0mH±20% | 18° | 2-2 | ≥1000PPS | ≥1500PPS | 7gf.cm | 40gf.cm | 1000PPS | 3000RPM | 14gf.cm | φ15mm*10.3mm |
| 5V | 10Ω±10% | 3.4mH±20% | 18° | 2-2 | ≥800PPS | ≥1000PPS | 7gf.cm | 30gf.cm | 700PPS | 2100RPM | 13gf.cm | φ15mm*11mm |
| 3.3V | 8.5Ω±10% | 2.9mH±20% | 18° | 2-2 | ≥950PPS | ≥1200PPS | 7gf.cm | 30gf.cm | 200PPS | 600RPM | 15gf.cm | φ15mm*10.6mm |
| 5V | 12Ω±10% | 4.0mH±20% | 18° | 2-2 | ≥1100PPS | ≥1500PPS | 7gf.cm | 30gf.cm | 800PPS | 2400RPM | 12gf.cm | φ15mm*11mm |
| 24V | 13Ω±10% | 4.0mH±20% | 18° | 2-2 | ≥1000PPS | ≥1500PPS | 13gf.cm | 30gf.cm | 1000PPS | 3000RPM | 30gf.cm | φ15mm*19.5mm |
Testimonial
Our 15mm stepper motors are bare units without built‑in drivers. Use common external bipolar drivers. Pick constant‑current type for higher pull‑out speed. Send over your speed and voltage specs, we can share practical driver suggestions.
Our 15mm stepper motor holds position without closed‑loop feedback for simple low‑speed positioning. BLDC motors spin faster for continuous run but need extra sensors. Choose stepper motors when you need stable positioning and tight BOM control.
Standard 15mm stepper motors use regular electroplated shafts and don’t pass salt‑spray tests. For humid or corrosive conditions, you can request upgraded shafts and anti‑corrosion grease, though this custom work adds extra cost.
Your 15mm stepper motor uses detent torque to hold light loads after power‑off. Note this passive holding force is far weaker than powered torque. It fits small valves, but cannot support heavy external loads.
Our regular 15mm stepper motors are 2‑phase bipolar with four leads for bipolar drive circuits. Unipolar versions are not standard stock. If your board only supports unipolar, contact our engineers for feasibility check.
Microstepping runs on your external driver, not the 15mm stepper motor itself. It smooths motion and reduces vibration, yet cannot eliminate its native mechanical step‑angle error. It mainly delivers quieter operation.
















